G3 Topsheet-Mounted Tail Connectors

Description

G3 Topsheet-Mounted Tail Connectors
Looking for ultra-fast transitions? Replace the tail connector on your G3 climbing skins with this lightweight and simple accessory to be lighter, faster, and more packable! These connectors mount permanently to your ski/board topsheet with a bomber adhesive. Sold as a pair Removes bulk from packed skins Super fast and easy transitions Compatible with any G3 climbing skins with holes in the tail strap Weighs just 2g each (saving 13g vs traditional tail clips) Fits skis and boards of any shape Mounts permanently Made in Canada Instructions: 1. Cleaning the Topsheet: a) Working at room temperature, wipe the tail end of the ski or board top sheet with isopropyl alcohol to remove any contaminants. 2. Tail Connector Placement: a) Put your skin on your ski or board to line up where the tail strap holes fall 3. Tail Connector Installation: a) PLEASE NOTE: Once the tail connector is placed on the ski or board topsheet, the tape will immediately bond. b) Before removing the red tape release liner, align the tail connector with the rounded edge pointed toward the tip of the ski or board c) Align the tail connector with your skin strap holes (see photo below) and apply tension to the strap d) Mark where the straight edge of the tail connector sits on your topsheet and remove the tail strap e) Remove the tape release liner from the back of the tail connector f) Place the tail connector on the ski or board top sheet where you previously marked g) Apply pressure for 30 seconds on the tail connector with the tape against the topsheet After application, the bond strength will increase as the adhesive wets out on the surface. At room temperature, approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. About Utah Ski Gear: Utah Ski Gear was established in 2011 and we believe that skiing is for everyone. Helping our customers find the right equipment to get them and their families skiing is our passion. We understand price can be the biggest deterrent and because of this we offer new and used skis on a budget. For the more experienced skier looking for advanced gear, we offer hard-to-find accessories like specialized tuning equipment and high-performance skis. Customers preferring maximum comfort while skiing can find electric boot heaters, such as Hotronic FootWarmers. Listing Notes: Photos are stock photos and are not the property of Utah Ski Gear.
G3 Topsheet-Mounted Tail Connectors
Looking for ultra-fast transitions? Replace the tail connector on your G3 climbing skins with this lightweight and simple accessory to be lighter, faster, and more packable! These connectors mount permanently to your ski/board topsheet with a bomber adhesive.
Sold as a pair
Removes bulk from packed skins
Super fast and easy transitions
Compatible with any G3 climbing skins with holes in the tail strap
Weighs just 2g each (saving 13g vs traditional tail clips)
Fits skis and boards of any shape
Mounts permanently
Made in Canada
Instructions:
1. Cleaning the Topsheet:
a) Working at room temperature, wipe the tail end of the ski or board top sheet with isopropyl alcohol to remove any contaminants.
2. Tail Connector Placement:
a) Put your skin on your ski or board to line up where the tail strap holes fall
3. Tail Connector Installation:
a) PLEASE NOTE: Once the tail connector is placed on the ski or board topsheet, the tape will immediately bond.
b) Before removing the red tape release liner, align the tail connector with the rounded edge pointed toward the tip of the ski or board
c) Align the tail connector with your skin strap holes (see photo below) and apply tension to the strap
d) Mark where the straight edge of the tail connector sits on your topsheet and remove the tail strap
e) Remove the tape release liner from the back of the tail connector
f) Place the tail connector on the ski or board top sheet where you previously marked
g) Apply pressure for 30 seconds on the tail connector with the tape against the topsheet After application, the bond strength will increase as the adhesive wets out on the surface. At room temperature, approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours.
About Utah Ski Gear:
Utah Ski Gear was established in 2011 and we believe that skiing is for everyone. Helping our customers find the right equipment to get them and their families skiing is our passion. We understand price can be the biggest deterrent and because of this we offer new and uséd skis on a budget. For the more experienced skier looking for advanced gear, we offer hard-to-find accessories like specialized tuning equipment and high-performance skis. Customers preferring maximum comfort while skiing can find electric boot heaters, such as Hotronic FootWarmers.
Listing Notes:
Photos are stock photos and are not the property of Utah Ski Gear.
×
×
×
×
Buy now and save!
Tell a friend
Visit store
Watch now
Postage info
Click the Postage tab above the listing description for more info
FREE Postage
Click the Postage tab above the listing description for more info!
Additional delivery notes
PICK UP OPTION
Sorry, our items are NOT available for pick-up.
PAYING VIA PAYPAL
We accept PayPal on our all our items so you can shop with confidence.
Simple choose the PayPal option when proceeding through the checkout.
Additional Information
No additional information at this time
Ask seller a question
You might also like
Roo Binding glue 16 OZ | Ski Binding Mounting Waterproof Adhesive Backshop
SVST Metal Grip Clear 3mm x 30cm | Sun Valley Ski Tools Core Shot Base Repair
SVST Metal Grip Black 3mm x 30cm | Sun Valley Ski Tools Core Shot Base Repair
130g ZF4 Arctic Paraffin Ski Wax by SVST Race Service 1
Contact
To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.
Ask seller a question
© Utah Ski Gear
Postage
Shipping is FREE for this item
Payment
Accepted Payment Methods
PayPal
Returns
Returns are accepted
Items must be returned within 60 days of the auction ending
Seller will pay for return shipping.
Additional Information:
USG ALL: Returns Accepted, Seller pays, 60 Days, Money Back
eBay integration
by